Corsair obsidian 1000d fan slots install#
Corsair obsidian 1000d fan slots full#
Corsair obsidian 1000d fan slots Pc#
Corsair obsidian 1000d fan slots series#

Unique to the 1000D, the power button and all USB ports have RGB LED backlighting in them lighting up that portion of the case I don’t recall seeing that in a chassis before. Other buttons/ports include the power and reset buttons and 3.5 mm jacks for headphone and microphone. Sparing little expense, the front panel is loaded with modern options including two USB 3.1 Type-C ports (a rarity to have one today), and four USB 3.0 ports for a lot of USB storage options.

Corsair obsidian 1000d fan slots series#

Both glass side panels use hinges at the back and open up for easier access.īuy Corsair Obsidian Series 1000D on Towards the bottom is space for the two power supplies as well as a Mini-ITX sized motherboard. The back panel has a total of seven expansion slots for PCIe, nine including the vertical GPU mounting space (video card can be mounted either way). The chassis supports eight fans up front (13 in total) to get cool air in the chassis. There is ample room in front for intake through its large dust filter (dust filters are also found on the rear, top, and bottom) so airflow shouldn’t be an issue. The louvered top is raised from the chassis allowing for air to exhaust, though perhaps not free-flowing. Where there isn’t glass, on top (the two flanking panels), there are brushed aluminum details adding to the overall high-end vibe it exudes. The exterior of the case is adorned by the smoke tinted tempered glass panels. The entire case, empty, weighs in at a hefty 65lbs making this thing a bit cumbersome to move around I'd image. The chassis measures in at a real estate-heavy 27.3” x 12.1” x 27.3” (LxWxH) which easily eclipses the 900D from years ago. The inside is designed to house some of the most ambitious and powerful PCs imaginable inside its dual-system, three-chambered layout. The exterior styling uses brushed aluminum and includes four smoke tempered glass panels which help give the Super-Tower a premium appearance that can be a focal point of an enthusiast build. It's not all about what can fit on the inside however that makes the case.

Corsair obsidian 1000d fan slots full#

So large in fact, it is able to house a complete E-ATX and Mini-ITX system concurrently - two motherboards, two power supplies, two full PCs in one case. Just as its name implies the case is quite large.

Corsair obsidian 1000d fan slots Pc#

I was always planning this, but even if I weren't, I would not keep the H150i as currently configured for very long because the tubing is just too stretched for my comfort level.A few days ago, Corsair announced the launch of its most ambitious and largest case yet with the new Obsidian 1000D Super-Tower PC Case. So ultimately, the H150i will get yanked and used to replace an AIO I have in an older build. Then I'm going to do a custom waterloop, overclock some more and benchmark some more. I'm going to overclock a bit, record some benchmarks, then delid the i9-7940x, then overclock some more and benchmark. My use of the H150i was always going to be temporary.

Corsair obsidian 1000d fan slots install#

It's possible, of course, to install the radiator on the opposite side, but that is pretty much equally as tight (I tested by sliding the fan tray over). So it's set up as push-pull using the LL's on the front-side. I have the AIO fans (the ML120s) installed on the backside to pull from the radiator. (If looking at it from the front of the case, it would be a mirror image, as follows): I have 4 LL120s attached to the fan bracket in the front, with the H150i installed as follows (viewed from within the case): The tubes are stretched very tight (which is what's putting slight sideways pressure on the DIMM module). It was really hard to install due to the length of tubing - it kept rotating the AIO's bracket such that it unattached from the cooler (from the heatsink/pump, I mean). I think it would either make more sense up top (requiring purchase of a 8 fan bracket from Corsair, although there is restricted airflow up there, so maybe not a great idea either), or just forgo the H150i and go with a custom loop where you can have tubing as long as you need.Īs I said, I got it working, but it was VERY close and is putting way more stress on both the H150i tubes, on the CPU bracket, on the DIMM module closest to the immediate right of the CPU chip. But I have to say that, having gotten it up and running that way, I wouldn't necessarily recommend it to anybody. And I've read somewhere on the forum that the H150i tubing would reach okay when installed at the front of the Obsidian 1000D case. Hey, I think I've read that you eventually wanted to use an H150i AIO in your build.